READY TO USE
DO NOT DILUTE!
CONCRETE DENSIFYING SOLUTION -
Penetrates to extraordinary depths permanently.
Waterproofs and improves new or old concrete.

bullet Purges out years of contamination and odours from old slabs.
bullet Early access, trafficable in one hour, minimum disruption.
bullet Tested to 150ft of Hydrostatic pressure and 300ft field tests.
bullet Will accept floor coverings or coatings after 24 hours.
bullet Protects against urine and chemical ingress.
bullet Environmentally safe and user friendly.
bullet Increases surface abrasion resistance.
bullet One time permanent application.
bullet Forms a permanent colloidal gel.
bullet Minimises acid/chemical attack
bullet Makes concrete more durable
bullet Easy and safe to apply.
bullet Prevents efflorescence.
 

[ View Densi-Proof Summary Intro in Chinese ]
看法Densi-Proof 总结介绍

  

[ View MSDS ]

  

[ View in printer friendly Adobe pdf format ]

HOW TO APPLY:
Note: in hot climates, mist-wet the surface with water and remove any puddles prior to application.

  1. Use medium to high-pressure airless sprayer complete with 60cm wand and a 0.019" fan tip spray jet.

  2. Hold spray tip 150mm from surface.

  3. Apply at point of saturation at the approximate rate of 4.5m2 per litre with an overlapping spray pattern of 10-15%.

  4. Begin applying at the lowest level elevation. For example, walls and slopes should be applied side to side, from the bottom up.

HOW TO USE AS A CURE:

  1. Follow normal application instructions, except use non-atomizing spray apparatus such as a pump tank sprayer. However, if surface is allowed to harden, you must then use an airless spray unit (at medium pressure to avoid disturbing the top).

  2. Apply to the newly placed finished surface as soon as it is practical to walk on without damaging.

  3. Apply at the rate of 4.5m2 per litre for broom finished concrete; 6 to 7m2 per litre on hard or steel trowelled concrete.

OTHER IMPORTANT NOTES:

  1. Wax, paint or anything else restricting access to concrete's interior must be chemically or mechanically removed for Protect Crete Densi-Proof to penetrate.

  2. Areas of high porosity have a faster penetration rate. These areas appear dry immediately after spraying and will require additional product.

  3. Do not apply on frozen substrate or when temperature is near freezing.

  4. When applying paint, adhesives or any other coatings, wait 24 hours after sealing with Protect Crete Densi-Proof, then flush clean surface with water and allow to dry before coating. Always follow coating manufacturers surface requirements.

  5. For very oily or greasy surfaces, use Protect Crete Densi-Proof plus Cleaner (or clean with detergent and high pressure hot water prior to application).

  6. Special note for concrete block: Block quality, cement content and porosity size can vary widely. Some may never be completely waterproofed and will only be damp proofed. Spray twice.

  7. Protect Crete Densi-Proof may etch glass or dull brushed and shiny aluminium and can be difficult to remove from other surfaces once it dries. Cover and mask surrounding surfaces or rinse immediately if sprayed.

  8. We recommend the use of a painters mask during application. Refer to MSDS.

User Friendly - Non Toxic - Non Flammable - Zero VOC - Environmentally Safe - Odourless

Manufacturers of the world’s most technically advanced systems for permanent concrete repair, moisture proofing and protection treatments.

20 Litres CONCRETE DENSIFYING SOLUTION - PERMANENTLY WATERPROOFS AND IMPROVES NEW OR OLD CONCRETE

Best viewed with Internet Explorer with screen resolution set to 1024 x 768

 This page was last updated on Monday November 24, 2008 22:02:04
Web design - Lozza - for Protecta-Crete™ trading as Protect Crete Pty Ltd and PROTOCRETE™ - Copyright (c) 2006-2008